Skip to content

Fleet tools

Fleet Recall Roundup

National Highway Traffic Safety Administration (NHTSA) safety recalls since 2010 for the vehicles and equipment public fleets run, plus Consumer Product Safety Commission (CPSC) recalls of the mowers, utility vehicles, tractors and power equipment public agencies use. Sort and filter by fleet class, make, model year and component, or open the list up to every vehicle.

Sources: NHTSA recall data and CPSC recalls · Updated nightly · Last refresh Nov. 20, 2026

This week’s top recalls for public fleets

Recalls NHTSA and CPSC posted Nov. 9, 2026 to Nov. 15, 2026, ranked by drive, parking and stop-using warnings, then by the kind of vehicle (emergency and passenger vehicles first) weighed against how many are affected. Updated every Monday.

  1. CPSC says stop using · Grounds and off-road equipment · 2,960 units Cummins Cummins Onan P5000iDF EFI Dual Fuel Portable Generators Generators and light towers · Nov. 12, 2026
  2. Fire apparatus · 937 vehicles Rosenbauer Avenger, Commander, Warrior Electrical system · Nov. 9, 2026
  3. Transit and coach bus · 1,182 vehicles New Flyer XD35, XD40, XD60 and 1 more Fuel system, diesel · Nov. 10, 2026
  4. Fleet SUV and car / Pickup, van and work truck · 314,029 vehicles Toyota Corolla, Tundra Air bags · Nov. 12, 2026
  5. Pickup, van and work truck · 62,490 vehicles Toyota Tundra Engine and engine cooling · Nov. 12, 2026

285 recalls · since 2010

  1. March 7, 2013 Terex Digger Derrick Utility and aerial 1999–2012 Equipment 261 units 13V089000

    Defect

    Terex South Dakota, Inc. (Terex) is recalling certain model year 1999-2012 XL4000 Digger Derrick utility trucks. The shims and spacers used to adjust the length of the hydraulic cylinder may give, causing the rod eye and threads to fatigue while lifting loads.

    Consequence

    The hydraulic cylinder may separate from the digger derick arm, allowing it to collapse without warning, increasing the risk of injury to the operator or those nearby.

    Remedy

    Terex will notify owners, and dealers will inspect and replace the rod eye and threads, as necessary. The existing shims and spacer will be replaced with a hardened spacer. All repairs will be made at no charge to the owner. The recall began on May 23, 2013. Owners may contact Terex at 1-605-882-4000.

    Terex South Dakota, Inc. · maker’s number SN602 · owners notified May 23, 2013 · NHTSA page for the 2012 Terex Digger Derrick ↗

  2. March 4, 2013 Terex Aerial Devices Utility and aerial 2012 Equipment 21 units 13V075000

    Defect

    Terex South Dakota, Inc. (Terex) is recalling certain model year 2012 utility trucks with SCM Aerial Devices. The lifting device's leveling arm may flex at the elbow and contact the boom structure. This may cause the leveling arm to break.

    Consequence

    If the leveling arm fails, the platform could tilt and the occupants may fall from the platform.

    Remedy

    Terex will notify owners, and dealers will replace the leveling arm free of charge. The recall began during April 2013. Owners may contact Terex at 1-605-882-4000.

    Terex South Dakota, Inc. · maker’s number SN604 · owners notified April 26, 2013 · NHTSA page for the 2012 Terex Aerial Devices ↗

  3. Oct. 24, 2012 Altec CFD 1217 Wood Chipper Utility and aerial 2011–2012 Equipment 205 units 12V517000

    Defect

    Altec is recalling certain model year 2011-2012 CFD 1217 wood chippers, manufactured between May 2011 through September 2012. The wood chipper blades were not made to hardness specifications.

    Consequence

    Due to not being the correct hardness, the wood chipper blades could fail during use causing the blade to separate. This could lead to personal injury.

    Remedy

    Altec will notify owners and will replace the blades, free of charge. The safety recall began on November 12, 2012. Owners may contact Altec at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number MAB 572 · owners notified Nov. 12, 2012 · NHTSA page for the 2012 Altec CFD 1217 Wood Chipper ↗

    Related on MPF: Altec Industries in the Solutions Guide

  4. Oct. 3, 2012 Altec Freightliner Utility and aerial 2011–2012 Service brakes, air: supply: hoses, lines/piping, and fittings 1,807 units 12V483000

    Defect

    Altec Industries, Inc. is recalling certain model year 2011-2012 vehicles mounted on a Freightliner chassis. Due to improper installation, the air supply line of the front brakes is susceptible to kinking.

    Consequence

    Overtime, the front brake line could become kinked leading to a loss of front brake control, increasing the risk of crash.

    Remedy

    Altec will notify owners, and will repair the vehicles, free of charge. The safety recall began on January 4, 2013. Owners may contact Altec Industries at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number MAB 571 · owners notified Jan. 4, 2013 · NHTSA page for the 2012 Altec Freightliner ↗

    Related on MPF: Altec Industries in the Solutions Guide

  5. Sept. 18, 2012 Altec AH100, AH75, AH85, HL125 Utility and aerial 2002–2009 Equipment 245 units 12V456000

    Defect

    Altec Industries, Inc. is recalling certain model year 2002-2009 AH75/85/100 and HL125 aerial device vehicles equipped with 16-foot radial outriggers. An improper torque was applied to the outrigger cylinder piston retention system during assembly. As a result, the cylinder could loosen from the rod allowing the outrigger leg to protrude beyond the confines of the chassis when it is in a stowed position.

    Consequence

    If the cylinder loosens from the rod, the outrigger could strike a person or object, increasing the risk of injury or property damage.

    Remedy

    Altec will notify owners, and will increase the torque on the piston free of charge. The safety recall began on November 6, 2012. Owners may contact Altec Industries at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 570 · owners notified Nov. 6, 2012 · NHTSA page for the 2009 Altec AH100 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  6. Aug. 30, 2012 Altec Digger Derrick Utility and aerial 2011–2012 Equipment 2,193 units 12V423000

    Defect

    Altec Industries, Inc. is recalling certain model year 2011-2012 Digger Derrick vehicles equipped with a PENGO digger extension shaft. A defect in the base material at the weld joint may result in a stress fracture through the applied weld of the drive hub to the hex bar material.

    Consequence

    The stress fracture could cause the extension shaft to separate from the drive hub when digging, increasing the risk of personal injury and/or property damage.

    Remedy

    Altec will notify owners, and will inspect the PENGO digger extension shaft and, as necessary, replace the shaft, free of charge. The safety recall began on October 12, 2012. Owners may contact Altec Industries at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 568 · owners notified Oct. 12, 2012 · NHTSA page for the 2012 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  7. Aug. 21, 2012 Altec AH100, AH85 Utility and aerial 2008–2009 Equipment 27 units 12V411000

    Defect

    Altec Industries, Inc. is recalling certain model year 2008-2009 Aerial Device vehicles due to improper welding processes used to manufacture the boom pivot pins. Failure of the pin could cause separation of the boom from the turntable.

    Consequence

    If the boom separates from the turntable, there is an increased risk of personal injury and/or property damage.

    Remedy

    Altec will notify owners, and will replace the pivot pins, free of charge. The safety recall began on September 12, 2012. Owners may contact Altec Industries at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number MAB 563 · owners notified Sept. 12, 2012 · NHTSA page for the 2009 Altec AH100 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  8. Aug. 8, 2012 Altec AT200A, AT235, AT235P, AT30-G, AT37-G, AT40M/P Utility and aerial 2012 Suspension: front: springs: torsion bar 141 units 12V390000

    Defect

    Altec Industries, Inc. is recalling certain model year 2012 Aerial Device vehicles built on a Navistar Terrastar chassis because the Altec-installed torsion bar increases the ride height of the front suspension, which when the vehicle hits bumps, may cause the vehicle to alter its steering direction.

    Consequence

    As the vehicle hits bumps, it may deviate from the intended line of travel, increasing the risk of a crash.

    Remedy

    Altec will notify owners, and will install an updated bracket and spring kit, free of charge. The safety recall began on August 27, 2012. Owners may contact Altec Industries at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 560 · owners notified Aug. 27, 2012 · NHTSA page for the 2012 Altec AT235P ↗

    Related on MPF: Altec Industries in the Solutions Guide

  9. Aug. 3, 2012 Altec DC1217, DC1317, DC1317HP Utility and aerial 2008–2011 Structure 227 units 12V383000

    Defect

    Altec Environmental Products (AEP) is recalling certain model year 2008-2009 DC1217 and DC1317 and model year 2008-2011 DC1317HP wood chippers. Cracks could develop in the wood chipper frame.

    Consequence

    If cracks develop in the frame, there is an increased risk of personal injury or property damage.

    Remedy

    AEP will notify owners, and dealers will install frame reinforcement kits to all affected units. The safety recall began on August 24, 2012. Owners may contact Altec Environmental Products at 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 551 · owners notified Aug. 24, 2012 · NHTSA page for the 2011 Altec DC1317HP ↗

    Related on MPF: Altec Industries in the Solutions Guide

  10. March 26, 2012 Altec AA755 Utility and aerial 1993–2004 Equipment: mechanical 1,222 units 12V127000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 1993-2004 AA755 AND AA755L VEHICLES. CONTINUOUS OVERLOADING OR SIDE LOADING OF THE BOOMS COULD CAUSE THE LOWER BOOM TO CRACK NEAR THE LOWER BOOM PIVOT.

    Consequence

    CONTINUED USE COULD CAUSE THE BOOM TO FAIL, INCREASING THE RISK OF INJURY TO PEOPLE OR PROPERTY BELOW.

    Remedy

    ALTEC WILL NOTIFY OWNERS, AND PROVIDE AA BOOM STIFFENER KIT. THE SAFETY RECALL BEGAN ON APRIL 20, 2012. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number 559 · owners notified April 20, 2012 · NHTSA page for the 2004 Altec AA755 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  11. Feb. 3, 2012 Altec AC18, AC23, AC38 Utility and aerial 2008–2011 Equipment: mechanical 18 units 12V041000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2008-2011 AC38 AND MODEL YEAR 2011 AC18 AND AC23 UTILITY VEHICLES, EQUIPPED WITH AN ANTI-TWO BLOCK (ATB) SWITCH TREE GUARD OPTION. THE ATB TREE GUARD SWITCH BRACKET MAY HAVE BEEN INSTALLED INCORRECTLY.

    Consequence

    IF THE BRACKET WAS INSTALLED INCORRECTLY, THE COMPONENTS COULD BE DISLODGED WHEN THE BOOM IS RAISED TOWARDS THE MAXIMUM ELEVATION AND COULD CAUSE THE ATB SWITCH, COVER, AND WEIGHT TO FALL, INCREASING THE RISK OF INJURY TO PEOPLE OR PROPERTY BELOW.

    Remedy

    ALTEC WILL NOTIFY OWNERS, AND INSTRUCT UNIT OWNERS TO INSPECT THE INSTALLATION OF THE TREE GUARD SWITCH BRACKET AND CORRECT ANY INCORRECT INSTALLATIONS. THE SAFETY RECALL BEGAN ON FEBRUARY 21, 2012. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 556 · owners notified Feb. 21, 2012 · NHTSA page for the 2011 Altec AC23 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  12. Dec. 21, 2011 Altec Digger Derrick Utility and aerial 2009–2011 Equipment: electrical 129 units 11V600000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 UTILITY VEHICLES EQUIPPED WITH SURE POWER BATTERY SEPARATOR DEVICES, PART NUMBER 16511893 (MODEL 1314) OR 16512967 (MODEL 1315). THE BATTERY SEPARATOR CAN OVERHEAT.

    Consequence

    OVERHEATING OF THE BATTERY SEPARATOR CAN RESULT IN SMOKE AND POSSIBLE FIRE.

    Remedy

    ALTEC WILL NOTIFY OWNERS AND REPLACE THE BATTER SEPARATORS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2012. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 554 · owners notified Jan. 11, 2012 · NHTSA page for the 2011 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  13. Nov. 9, 2011 Terex XT55 Utility and aerial 2007–2009 Equipment 5,123 units 11V542000

    Defect

    TEREX IS RECALLING CERTAIN MODEL YEAR 1997 THROUGH 2009 XT55 AERIAL DEVICES MOUNTED ON TRUCKS. THESE VEHICLES ARE USED TO ELEVATE PERSONNEL TO TRIM TREES AND FOR UTILITY WORK WHILE PARKED IN THE WORK AREA. CRACKS CAN DEVELOP AROUND THE LOWER BOOM HINGE PIN BOSS AT THE TURNTABLE WHICH CAN PROGRESS INTO FAILURE OF THE PLATES IF NOT DETECTED.

    Consequence

    FAILURE OF THE PLATES WILL CAUSE UNEXPECTED MOTION OF THE BOOM AND COULD CAUSE THE PLATFORM TO FALL, RESULTING IN SERIOUS INJURY OR DEATH TO A PERSON STANDING ON THE PLATFORM.

    Remedy

    TEREX WILL NOTIFY OWNERS AND WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 7, 2011. OWNERS MAY CONTACT TEREX UTILITIES WARRANTY DEPARTMENT AT 1-605-884-3892.

    TEREX SOUTH DAKOTA, INC. · maker’s number SN598 · owners notified Dec. 7, 2011 · NHTSA page for the 2009 Terex XT55 ↗

  14. Oct. 5, 2011 Altec AH100, AH75, AH85 Utility and aerial 2010 Equipment 22 units 11V498000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2010 AH75, AH85 AND AH100 AERIAL DEVICES MANUFACTURED FROM JUNE 29, 2010, THROUGH DECEMBER 26, 2010, FOR FAILURE OF THE PLATFORM LEVELING SYSTEM.

    Consequence

    FAILURE OF THE PLATFORM LEVELING SYSTEM CAN RESULT IN UNINTENDED PLATFORM MOVEMENT INCREASING THE RISK OF DEATH OR SERIOUS INJURY.

    Remedy

    ALTEC WILL NOTIFY OWNERS, AND ALTEC DEALERS WILL MODIFY THE PLATFORM LEVELING SYSTEM AS NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 4, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-GO-ALTEC (1-877-462-5832) FOR MORE INFORMATION.

    ALTEC INDUSTRIES INC. · maker’s number MAB 555 · owners notified Oct. 4, 2011 · NHTSA page for the 2010 Altec AH100 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  15. Sept. 1, 2011 Altec Digger Derrick Utility and aerial 2011 Equipment 35 units 11V451000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2011 DL/DM SERIES, D4000A, AND DB37 DIGGER DERRICK SERVICE UTILITY VEHICLES MANUFACTURED FROM JANUARY 2011 THROUGH APRIL 2011, EQUIPPED WITH PQ SINGLE AXIS BOOM CONTROLLERS. THE MECHANICAL INTERLOCK (LOCK OUT) MAY NOT OPERATE PROPERLY.

    Consequence

    IF THE CONTROL INTERLOCK DOES NOT FUNCTION PROPERLY, THE CONTROL HANDLE CAN BE ACCIDENTLY SHIFTED CAUSING MOVEMENT OF THE UNIT, POSSIBLY RESULTING IN SERIOUS INJURY OR DEATH.

    Remedy

    ALTEC WILL NOTIFY OWNERS, AND ALTEC DEALERS WILL REPLACE THE HAND CONTROLLERS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 7, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-GO-ALTEC (1-877-462-5832) FOR MORE INFORMATION.

    ALTEC INDUSTRIES INC. · maker’s number CSN 550 · owners notified Sept. 7, 2011 · NHTSA page for the 2011 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  16. Aug. 8, 2011 Terex HR37, HR40 Utility and aerial 2000–2001 Equipment 109 units 11V418000

    Defect

    TEREX IS RECALLING CERTAIN MODEL YEAR 2000 AND 2001 HR37M AND HR40M UTILITY TRUCKS MANUFACTURED FROM NOVEMBER 2000 THROUGH DECEMBER 2001. THE AERIAL DEVICES INSTALLED ON THESE TRUCKS MAY CONTAIN A LOWER BOOM LIFT CYLINDER WITH DEFECTIVE COMPONENTS. THE MATERIAL USED TO PRODUCE THE CYLINDER ROD ENDS WAS NOT TO SPECIFICATIONS.

    Consequence

    THE CYLINDER ROD ENDS MAY CRACK CAUSING THE CYLINDER TO DISCONNECT WHILE IN USE. PERSONAL INJURY OR DEATH CAN OCCUR TO THE USER OR TO PERSONS AROUND THE VEHICLE.

    Remedy

    TEREX WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE CYLINDER ROD ENDS FOR CRACKS. DEALERS WILL ALSO TEST THE CYLINDER MATERIAL FOR HARDNESS. THE SAFETY RECALL BEGAN ON AUGUST 30, 2011. OWNERS MAY CONTACT TEREX UTILITIES WARRANTY DEPARTMENT BY CALLING 1-605-884-3892 OR EMAIL TO UTILITIES.WARRANTY@TEREX.COM.

    TEREX TELELECT, INC. · maker’s number SN579 · owners notified Aug. 30, 2011 · NHTSA page for the 2001 Terex HR40 ↗

  17. Aug. 3, 2011 Altec Service Body Utility and aerial 2009–2011 Latches/locks/linkages: doors: latch 4,500 units 11V397000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2009-2011 SERVICE UTILITY BODY VEHICLES MANUFACTURED FROM MAY 2009 THROUGH MAY 2011. THE COMPARTMENT LATCH MAY FAIL IN THE SECONDARY (SAFETY CATCH) POSITION.

    Consequence

    THE COMPARTMENT DOOR ON THE UTILITY SERVICE BODY COULD COME OPEN DURING TRANSIT IF THE PRIMARY LATCHING POSITION IS NOT ENGAGED. A PERSON OR OBJECT COULD THEN FALL FROM THE VEHICLE DURING OPERATION, CAUSING INJURY AND/OR PROPERTY DAMAGE.

    Remedy

    ALTEC WILL DIRECT THE CUSTOMERS TO INSPECT THE COMPARTMENT DOOR LATCHES AND REPLACE ANY THAT DO NOT HOLD IN THE SECONDARY LATCHING POSITION. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 7, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 546 · owners notified Sept. 7, 2011 · NHTSA page for the 2011 Altec Service Body ↗

    Related on MPF: Altec Industries in the Solutions Guide

  18. Aug. 1, 2011 Altec Aerial Device Utility and aerial 1997–2009 Equipment: electrical 67 units 11V389000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 1997-2009 AERIAL DEVICES MANUFACTURED FROM JUNE 1997 THROUGH JULY 2009, EQUIPPED WITH A BCM 44B ELECTRICAL LEAKAGE MONITORING SYSTEM. THE METER WAS INCORRECTLY INSTALLED AND THE WIRING MAY COME LOOSE; HOWEVER, THE METER COULD STILL INDICATE THAT IT IS WORKING PROPERLY.

    Consequence

    FAILURE OF THE LEAKAGE MONITORING SYSTEM CAN RESULT IN THE USER TOUCHING A CONDUCTOR, UNAWARE THAT IT MAY BE ENERGIZED AND RISKING ELECTRICAL SHOCK OR ELECTROCUTION.

    Remedy

    ALTEC WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 7, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 549 · owners notified Sept. 7, 2011 · NHTSA page for the 2009 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  19. Aug. 1, 2011 Altec DC912A, WC126A Utility and aerial 2009–2011 Suspension: rear: axle: spindle 210 units 11V387000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2009-2011 DC-912A AND MODEL YEAR 2010 AND 2011 WC126A WOOD CHIPPERS MANUFACTURED FROM JANUARY 2009 THROUGH JULY 2011. FATIGUE FAILURES CAN OCCUR AT THE BEARING GREASE HOLE LOCATED ON THE AXLE SPINDLE.

    Consequence

    THE SPINDLE ON THE AXLE COULD FAIL ALLOWING THE WHEEL TO SEPARATE FROM THE CHIPPER, POSSIBLY RESULTING IN A CRASH.

    Remedy

    ALTEC WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE AXLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 17, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-435-9258.

    ALTEC INDUSTRIES INC. · maker’s number MAB 547 · owners notified Aug. 17, 2011 · NHTSA page for the 2011 Altec DC912A ↗

    Related on MPF: Altec Industries in the Solutions Guide

  20. July 28, 2011 Altec Aerial Device Utility and aerial 2010–2011 Electrical system: 12v/24v/48v battery: cables 63 units 11V386000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2010-2011 AERIAL DEVICES UTILITY VEHICLES MANUFACTURED FROM AUGUST 2010 THROUGH MAY 2011, THE BATTERY FUSE BLOCK MAY BE INSTALLED INCORRECTLY. THE POWER SOURCE MAY HAVE BEEN CONNECTED TO THE WRONG SIDE (POST) OF THE FUSE LEAVING THE BATTERY HOT CABLE UNPROTECTED WITHOUT A FUSE.

    Consequence

    THE CHASSIS BATTERIES COULD SHORT AND CAUSE A FIRE INCREASING THE RISK OF DEATH OR SERIOUS INJURY.

    Remedy

    ALTEC WILL INSPECT THE CONNECTION OF THE BATTERY CABLE TO THE FUSE BLOCK, THE POSITION OF THE FUSE BLOCK MOUNTING PLATE ON THE BATTERY, AND REPAIR THE VEHICLES AS NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 1, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 548 · owners notified Aug. 1, 2011 · NHTSA page for the 2011 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  21. June 6, 2011 Altec AA50, AA55, AA60, AA600, AA755, AM55 and 13 more Utility and aerial 2009–2010 Equipment 56 units 11V318000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2009-2010 AERIAL DEVICES AND DIGGER DERRICKS UTILITY VEHICLES MANUFACTURED FROM APRIL 2009 THROUGH MAY 2010. THE HIGH STRENGTH FASTENERS THAT CONNECT THE BOOM TURNTABLE TO THE PEDESTAL MAY FAIL DUE TO STRESS CORROSION CRACKING, WHICH COULD CAUSE THE BOOM TO FALL.

    Consequence

    A FALLING BOOM MAY CAUSE INJURY TO THE USER OR PEOPLE NEARBY AND DAMAGE TO PERSONAL PROPERTY.

    Remedy

    ALTEC WILL REPLACE THE FASTENERS TO CORRECT THIS CONDITION, FREE OF CHARGE. THE SAFETY RECALL BEGAN DURING JUNE 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 541A · owners notified June 22, 2011 · NHTSA page for the 2010 Altec AM855 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  22. May 24, 2011 Altec DM45, DM47, DM50 Utility and aerial 2008–2009 Equipment 227 units 11V297000

    Defect

    ALTEC IS RECALLING CERTAIN MODEL YEAR 2008-2009 DM 45, DM 47 AND DM 50 DIGGER DERRICK UTILITY VEHICLES MANUFACTURED FROM JANUARY 2010 THROUGH SEPTEMBER 2010. THESE UNITS MAY HAVE CRACKS IN THE BOOM LIFT CYLINDER ROD EYE CASTING THAT CAN CAUSE THE CASTING TO FAIL.

    Consequence

    IF THE ROD EYE CASTING FAILS, THE BOOM MAY SUDDENLY FALL CAUSING DEATH OR SERIOUS INJURY.

    Remedy

    ALTEC WILL INSPECT THE LIFT CYLINDER ROD EYE CASTING FOR CRACKS. ANY CYLINDERS FOUND WITH CRACKS WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING JUNE 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 545 · owners notified May 31, 2011 · NHTSA page for the 2009 Altec DM45 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  23. May 20, 2011 Terex TCP40 Utility and aerial 2009–2010 Equipment 65 units 11V301000

    Defect

    TEREX IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 TCP40 UTILITY TRUCKS MANUFACTURED FROM JANUARY 2009 THROUGH NOVEMBER 2010. A LOWER CONTROL LEVER MAY HAVE A DEFECT THAT ALLOWS UNINTENDED MOVEMENT OF THE BOOM OR BUCKET.

    Consequence

    UNINTENDED MOVEMENT OF THE BOOM OR BUCKET COULD RESULT IN INJURIES TO THE OPERATOR OR OTHERS.

    Remedy

    TEREX WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 30, 2011. OWNERS MAY CONTACT TEREX UTILITIES WARRANTY DEPARTMENT BY CALLING 1-605-884-3892 OR EMAIL TO UTILITIES.WARRANTY@TEREX.COM.

    TEREX TELELECT, INC. · maker’s number SN595 · owners notified June 30, 2011 · NHTSA page for the 2010 Terex TCP40 ↗

  24. May 16, 2011 Altec AT40M/P Utility and aerial 2007–2009 Equipment: electrical 103 units 11V284000

    Defect

    ALTEC IS RECALLING CERTAIN AT40M/P AERIAL DEVICES MANUFACTURED FROM JUNE 2007 THROUGH OCTOBER 2009. THESE UNITS HAVE FIBERGLASS ARM LINKS THAT, OVER TIME, MAY DEVELOP REDUCED ELECTRICAL ISOLATION PERFORMANCE. AS SUCH, THE LINKS MAY BEGIN TO CONDUCT CURRENT.

    Consequence

    IF THE ARM LINK CONDUCTS CURRENT, SHOULD THE ARM LINK CONTACT AN ELECTRICAL WIRE, THE OPERATOR MAY BE SHOCKED OR ELECTROCUTED AND DEATH OR SERIOUS INJURY MAY RESULT.

    Remedy

    ALTEC WILL REPLACE THE LINK FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 23, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC INDUSTRIES INC. · maker’s number CSN 544 · owners notified May 23, 2011 · NHTSA page for the 2009 Altec AT40M/P ↗

    Related on MPF: Altec Industries in the Solutions Guide

  25. April 14, 2011 Altec DC912A Utility and aerial 2009–2010 Wheels: lugs/nuts/bolts/studs 132 units 11V238000

    Defect

    AEP IS RECALLING CERTAIN MODEL YEAR 2009-2010 DC912A CHIPPER UNITS MANUFACTURED FROM JANUARY 2009, THROUGH SEPTEMBER 2010, FOR WHEEL LUG NUTS THAT MAY BECOME LOOSE ALLOWING THE WHEEL AND/OR TIRE TO COME OFF WHILE TRAVELING.

    Consequence

    IF THE WHEEL AND TIRE COMES OFF WHILE TRAVELING, DEATH OR SERIOUS INJURY MAY RESULT.

    Remedy

    AEP WILL REPLACE THE AXLE HUB/DRUMS AND WHEEL RIMS THAT HAVE BEEN REPEATEDLY LOOSE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 20, 2011. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.

    ALTEC ENVIRONMENTAL PRODUCTS, LLC · maker’s number CSN 543 · owners notified April 20, 2011 · NHTSA page for the 2010 Altec DC912A ↗

    Related on MPF: Altec Industries in the Solutions Guide

Recall details are NHTSA’s and CPSC’s own text. Fleet classes are MPF’s grouping of NHTSA makes and models; police variants are often filed under the civilian model name, so also search the civilian model. Check every vehicle by VIN at nhtsa.gov/recalls.