Skip to content

Fleet tools

Fleet Recall Roundup

National Highway Traffic Safety Administration (NHTSA) safety recalls since 2010 for the vehicles and equipment public fleets run, plus Consumer Product Safety Commission (CPSC) recalls of the mowers, utility vehicles, tractors and power equipment public agencies use. Sort and filter by fleet class, make, model year and component, or open the list up to every vehicle.

Sources: NHTSA recall data and CPSC recalls · Updated nightly · Last refresh Nov. 20, 2026

This week’s top recalls for public fleets

Recalls NHTSA and CPSC posted Nov. 9, 2026 to Nov. 15, 2026, ranked by drive, parking and stop-using warnings, then by the kind of vehicle (emergency and passenger vehicles first) weighed against how many are affected. Updated every Monday.

  1. CPSC says stop using · Grounds and off-road equipment · 2,960 units Cummins Cummins Onan P5000iDF EFI Dual Fuel Portable Generators Generators and light towers · Nov. 12, 2026
  2. Fire apparatus · 937 vehicles Rosenbauer Avenger, Commander, Warrior Electrical system · Nov. 9, 2026
  3. Transit and coach bus · 1,182 vehicles New Flyer XD35, XD40, XD60 and 1 more Fuel system, diesel · Nov. 10, 2026
  4. Fleet SUV and car / Pickup, van and work truck · 314,029 vehicles Toyota Corolla, Tundra Air bags · Nov. 12, 2026
  5. Pickup, van and work truck · 62,490 vehicles Toyota Tundra Engine and engine cooling · Nov. 12, 2026

285 recalls · since 2010

  1. March 23, 2020 Altec Digger Derrick Utility and aerial 2019–2020 Equipment 60 units 20V174000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2019-2020 DT65-E, D3000-E, and DH-E Digger Derricks Aerial devices. Operators could inadvertently open the pole guide while performing other tasks, possibly resulting in a loss of control of the load.

    Consequence

    If the pole guide is opened while performing other operations, the pole may become unbalanced and cause loss of control of the load, increasing the risk of injury or death.

    Remedy

    Altec will notify owners and will install a guard kit over the pole guide controls, free of charge. The recall began May 5, 2020. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 754.

    Altec Industries Inc. · maker’s number CSN 754 · owners notified May 5, 2020 · NHTSA page for the 2020 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  2. March 20, 2020 Terex SML, TCX Utility and aerial 2009–2016 Equipment 6 units 20V168000

    Defect

    Terex South Dakota, Inc. (Terex) is recalling certain 2009-2016 TCX60/85 and SML65/90 aerial devices. The rod eyes on the 25ft lift cylinders may fail prematurely.

    Consequence

    If the rod eye fails the lift boom will drift down. The remaining cylinder may not support the boom fully and will slowly leak down. These scenarios increase the risk of an injury.

    Remedy

    Terex will notify owners, and dealers will replace the rod eyes and shims, free of charge. The recall began April 9, 2020. Owners may contact Terex customer service at 1-605-882-4000. Terex's number for this recall is SN684.

    Terex South Dakota, Inc. · maker’s number SN684 · owners notified April 9, 2020 · NHTSA page for the 2016 Terex TCX ↗

  3. Feb. 27, 2020 Altec L42M, LR756, LR758, LR760, LR760-E70, TDA58 Utility and aerial 2019 Equipment 238 units 20V115000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2019 LR7 Series, TDA58 and L42M Aerial Devices. The high strength fasteners used to secure the pedestal to the turntable may fail.

    Consequence

    If the fasteners break, the pedestal may separate from turntable, increasing the risk of injury or death.

    Remedy

    Altec will notify owners and will inspect and replace the fasteners if necessary, free of charge. The recall began April 22, 2020. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this campaign is CSN 750.

    Altec Industries Inc. · maker’s number CSN 750 · owners notified April 22, 2020 · NHTSA page for the 2019 Altec TDA58 ↗

    Related on MPF: Altec Industries in the Solutions Guide

  4. Feb. 24, 2020 Terex Tm-Series Utility and aerial 2011–2020 Equipment 523 units 20V103000

    Defect

    Terex South Dakota, Inc. (Terex) is recalling certain 2014-2019 TM bucket/boom trucks. The limit switch was installed upside down and does not stop platform level movement if the platform level exceeds 15 degrees.

    Consequence

    If the platform level limit switch does not stop the platform from tilting, a platform occupant could fall, increasing the risk of an injury.

    Remedy

    Terex will notify owners, and dealers will properly install the limit switch, free of charge. The recall began April 14, 2020. Owners may contact Terex customer service at 1-605-882-4000. Terex's number for this recall is SN681.

    Terex South Dakota, Inc. · maker’s number SN681 · owners notified April 14, 2020 · NHTSA page for the 2020 Terex Tm-Series ↗

  5. Jan. 22, 2020 Altec Crane Utility and aerial 2015–2019 Equipment 96 units 20V034000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2015-2019 Altec AC26, AC28, AC30, and AC38 Crane Aerial Devices. The boom lift cylinder hose may have been connected to a port that does not have an internal velocity fuse. Failure of a boom lift cylinder hose that is not protected by a velocity fuse can result in uncontrolled boom movement.

    Consequence

    Uncontrolled movement of the boom lift increases the risk of injury.

    Remedy

    Altec will notify owners and will inspect the hose to verify that it is connected properly, repairing it as necessary, free of charge. The recall began January 30, 2020. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is MAB 748.

    Altec Industries Inc. · maker’s number MAB 748 · owners notified Jan. 30, 2020 · NHTSA page for the 2019 Altec Crane ↗

    Related on MPF: Altec Industries in the Solutions Guide

  6. Jan. 17, 2020 Terex Advance FD4000, FD5000GL, FD7000B, FDC300 Utility and aerial 2020 Power train: axle assembly: axle shaft 34 units 20V023000

    Defect

    Terex Advance Mixer (Terex) is recalling certain 2020 FDC300, FD4000, FD5000GL, and FD7000B vehicles. The axle output shafts were incorrectly heat treated, possibly causing them to fracture.

    Consequence

    The fracturing of the output shaft would result in a loss of drive, increasing the risk of a crash.

    Remedy

    Terex has notified owners. Owners should inspect the Dana output flange for its production date. Dana will replace any that are in the affected range, free of charge. The recall began January 24, 2020. Owners may contact Terex customer service at 1-800-678-5961.

    Terex Advance Mixer, Inc. · owners notified Jan. 24, 2020 · NHTSA page for the 2020 Terex Advance FDC300 ↗

  7. Oct. 30, 2019 Altec Aerial Device Utility and aerial 2018–2019 Equipment 15 units 19V779000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2018-2019 AT200A, AT235, AT235P, AT37-G, AT40-G and AT248F Aerial Devices. The aerial devices have not been stability tested in accordance with ANSI A92.2.

    Consequence

    An unstable aerial device may suddenly collapse, increasing the risk of injury or death.

    Remedy

    Altec will notify owners, instructing them to perform a stability test. The recall began December 16, 2019. Owners may contact Altec customer service at 1-877-462-5832.

    Altec Industries Inc. · maker’s number CSN 741 · owners notified Dec. 16, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  8. Oct. 4, 2019 Altec Digger Derrick Utility and aerial 2016–2019 Equipment 275 units 19V710000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2016-2019 Altec D2/3/4B, DLB, DMB, DHB, DT65 and DT80 Digger Derrick vehicles. The outrigger valves may be plumbed incorrectly. As a result, the outriggers could continue retracting after an operator has stopped controlling them.

    Consequence

    If the outriggers continue to retract without command, the unit may become unstable and collapse, increasing the risk of injury or death to those nearby.

    Remedy

    Altec will notify owners, and dealers will inspect the outrigger valve plumbing correcting it as necessary, free of charge. The recall began November 25, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 739.

    Altec Industries Inc. · maker’s number CSN 739 · owners notified Nov. 25, 2019 · NHTSA page for the 2019 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  9. Sept. 18, 2019 Altec Aerial Device Utility and aerial 2019 Electrical system: integrated trailer brake control 15 units 19V662000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2019 LR7-Series aerial devices. The trailer brake controller may be improperly grounded.

    Consequence

    A trailer brake controller with improper grounding may result in the trailer intermittently braking when needed, increasing risk of a crash.

    Remedy

    Altec will notify owners, and direct them to inspect the brake controller for proper grounding, and if applicable, correct any that are improperly grounded. The recall began November 4, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 737.

    Altec Industries Inc. · maker’s number CSN 737 · owners notified Nov. 4, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  10. Sept. 17, 2019 Terex TLM Utility and aerial 2016–2017 Equipment 42 units 19V659000

    Defect

    Terex South Dakota, Inc. (Terex) is recalling certain TLM aerial-device vehicles equipped with external holding valve blocks. The incorrect holding valve was installed on the upper boom cylinder base end. As a result, if the hose for the upper boom raise function should burst while at maximum load and maximum side reach, the boom may drift down.

    Consequence

    Uncontrolled movement of the boom can increase the risk of an injury.

    Remedy

    Terex will notify owners, and dealers will replace the base end holding valve on the upper boom lift cylinder, free of charge. The recall began October 25, 2019. Owners may contact Terex customer service at 1-844-837-3948. Terex's number for this recall is SN675.

    Terex South Dakota, Inc. · maker’s number SN675 · owners notified Oct. 25, 2019 · NHTSA page for the 2017 Terex TLM ↗

  11. Aug. 15, 2019 Altec Aerial Device Utility and aerial 2012–2019 Equipment: mechanical: winch 23 units 19V602000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2012-2019 Altec AM60E, AA55E, AH75/85/100, AH125, and AH150 Aerial Devices. The recovery winch valve may allow the winch to lift more than it is rated for.

    Consequence

    If the recovery winch attempts to lift more than it is rated for, it can increase the risk of an injury or death.

    Remedy

    Altec will notify owners, and instruct owners to inspect the winch pressures and install an external pressure relief valve, if necessary, free of charge. The recall began October 7, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 734.

    Altec Industries Inc. · maker’s number CSN 734 · owners notified Oct. 7, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  12. Aug. 6, 2019 Altec Aerial Device Utility and aerial 2018–2019 Equipment 118 units 19V578000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2018-2019 LR7, TA50, TA55, TA60 and TDA58 Aerial Devices. The high strength fasteners used to secure the pedestal to the turntable may fail.

    Consequence

    If the fasteners break, the pedestal may separate from turntable, increasing the risk of injury or death.

    Remedy

    Altec has notified owners, and dealers will inspect the fasteners, replacing them as necessary, free of charge. The recall began August 9, 2019. Owners may contact Altec customer service at 1-877-462-5832.

    Altec Industries Inc. · maker’s number MAB 732 · owners notified Aug. 9, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  13. Aug. 5, 2019 Altec Aerial Device Utility and aerial 2016–2019 Equipment 32 units 19V573000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2017-2019 LS60 Aerial Devices. The aerial devices may not meet all aerial level ground and slope stability requirements, allowing the units to become unstable and possibly overturn.

    Consequence

    An unstable aerial device can increase the risk of injury.

    Remedy

    Altec will notify owners, instructing them to replace the unit load charts, adjust the Hydraulic Overload Protection (HOP) settings, verify the unit has the proper counterweight, and perform a stability test. The recall began September 13, 2019. Owners may contact Altec customer service at 1-877-462-5832.

    Altec Industries Inc. · maker’s number CSN 730 · owners notified Sept. 13, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  14. July 2, 2019 Altec Aerial Device Utility and aerial 2018–2019 Equipment 59 units 19V508000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2018-2019 AT37/41/48 and L37/42/44 Aerial Devices. The high strength fasteners used to secure the pedestal to the turntable may fail.

    Consequence

    If the fasteners fail, the pedestal may separate from the turntable, increasing the risk of injury or death.

    Remedy

    Altec will notify owners, and dealers will replace the fasteners, free of charge. The recall began August 22, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 725.

    Altec Industries Inc. · maker’s number CSN 725 · owners notified Aug. 22, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  15. June 21, 2019 Altec Aerial Device Utility and aerial 2003–2019 Service brakes, air 957 units 19V483000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2003-2019 Altec TA45, TA50, TA55, TA60, L37, L39, LRV, LR7, A-T40C, T40P and AP45 vehicles equipped with air-cushioned pintle hitch and/or accessory air components. The accessories utilizing chassis air supply may be missing pressure protection valves. The accessory lines may not prevent service brake line pressure loss due to failure or leakage in the accessory air system. Additionally, the air cushioned pintle hook may have been connected to the incorrect air lines. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."

    Consequence

    Loss of service brake pressure can increase the risk of a crash.

    Remedy

    Altec will notify owners, and dealers will inspect the pressure protection installation and repair any unit that does not pass inspection, free of charge. The recall began August 15, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 724.

    Altec Industries Inc. · maker’s number CSN 724 · owners notified Aug. 15, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  16. June 17, 2019 Altec AD108, Hliw-T Utility and aerial 2003–2019 Service brakes, air: supply: hoses, lines/piping, and fittings 328 units 19V465000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2003-2019 Altec AD108 Cable handlers and HLIW-T Trailer Mounted Insulator Washer vehicles. The vehicles may be equipped with non-DOT brake line fittings that may leak at the air fittings. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 106, "Brake Hoses."

    Consequence

    If the brake lines leak, the parking brake may drag, increasing the risk of crash.

    Remedy

    Altec will notify owners, and dealers will inspect the vehicles and replace the brake line air fittings if necessary, free of charge. The recall began July 31, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 723.

    Altec Industries Inc. · maker’s number CSN 723 · owners notified July 31, 2019 · NHTSA page for the 2019 Altec Hliw-T ↗

    Related on MPF: Altec Industries in the Solutions Guide

  17. June 17, 2019 Altec Aerial Device Utility and aerial 2017–2018 Equipment 542 units 19V455000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2017-2018 LR7, TA50/55/60 and L42/45 Aerial Devices. Multiple fasteners used to secure the rotation bearing may break, possibly resulting in the pedestal separating from the turntable.

    Consequence

    If the pedestal separates from the turntable, it can increase the risk of injury or death.

    Remedy

    Altec will notify owners, and dealers will replace the affected fasteners, free of charge. The recall began July 31, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 722.

    Altec Industries Inc. · maker’s number CSN 722 · owners notified July 31, 2019 · NHTSA page for the 2018 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  18. June 4, 2019 Altec Aerial Device Utility and aerial 2016–2019 Equipment 435 units 19V409000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2016-2019 LR7 Series Aerial Devices. The aerial device can be operated without the rear outriggers being deployed, which may cause the unit to be unstable.

    Consequence

    An unstable aerial device may suddenly collapse, increasing the risk of injury.

    Remedy

    Altec will notify owners, and dealers will inspect the vehicles and correct them to require the proper outrigger operation, as necessary, free of charge. The recall began July 25, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 720.

    Altec Industries Inc. · maker’s number CSN 720 · owners notified July 25, 2019 · NHTSA page for the 2019 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  19. May 13, 2019 Altec Digger Derrick Utility and aerial 2009–2019 Equipment: other: labels 1,036 units 19V365000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2009-2019 DL/DM, DL/DMB, DH, D/2/3/4, and DC Digger Derrick vehicles. The slope indicator placard card may falsely indicate that the unit could be used without leveling on a 5 degree slope.

    Consequence

    An operator may improperly set up the unit, making the unit unstable, thus increasing the risk of injury.

    Remedy

    Altec will notify owners, and issue CSN 719 to owners, instructing them to remove the incorrect placards, free of charge. The recall began July 2, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 719.

    Altec Industries Inc. · maker’s number CSN 719 · owners notified July 2, 2019 · NHTSA page for the 2019 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  20. April 15, 2019 Altec Aerial Device Utility and aerial 2017–2018 Equipment: mechanical 153 units 19V303000

    Defect

    Altec Industries Inc. (Altec) is recalling certain 2017-2018 Altec LR7, TA50, TA55, TA60, and TA45M-T50 Aerial Devices. The fasteners that are used to secure the turntable to the pedestal may fail.

    Consequence

    If multiple fasteners fail, the pedestal and turntable may separate, increasing the risk of death or injury.

    Remedy

    Altec has notified owners and dealers will inspect and replace the defective fasteners, free of charge. The recall began April 18, 2019. Owners may contact Altec customer service 1-877-462-5832. Altec's number for this recall is MAB 716.

    Altec Industries Inc. · maker’s number MAB 716 · owners notified April 18, 2019 · NHTSA page for the 2018 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  21. March 1, 2019 Terex Advance Front Discharge Concrete Utility and aerial 2018–2019 Service brakes, air: disc: caliper 98 units 19V152000

    Defect

    Terex Advance Mixer, Inc is recalling certain 2018-2019 Front Discharge Concrete Mixer Trucks equipped with Meritor EX225 disc brake calipers. The drive pins, a component with the axle sub-assembly, may have been cracked during assembly, possibly resulting in the pins fully fracturing.

    Consequence

    If the drive pin becomes fully fractured, the vehicle may pull to one side while braking, causing a loss of vehicle control and increasing the risk of crash.

    Remedy

    Terex will notify owners and Meritor dealers will inspect and replace the brake calipers, free of charge. The recall began April 23, 2019. Owners may contact Terex Advance customer service at 1-605-882-4000.

    Terex Advance Mixer, Inc. · owners notified April 23, 2019 · NHTSA page for the 2019 Terex Advance Front Discharge Concrete ↗

  22. Feb. 27, 2019 Altec Digger Derrick Utility and aerial 2003–2019 Equipment 14,389 units 19V127000

    Defect

    Altec Industries, Inc (Altec) is recalling certain 2003-2019 Altec DL/DM, DL/DMB, and DC Digger Derrick vehicles. The pedestal tube welds may crack over time.

    Consequence

    Unrepaired cracks may result in failure of the pedestal and uncontrolled movement increasing the risk of injury.

    Remedy

    Altec will notify owners and will provide repairs as necessary and a reinforcing kit. The recall began April 3, 2019. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is CSN 713.

    Altec Industries Inc. · maker’s number CSN 713 · owners notified April 3, 2019 · NHTSA page for the 2019 Altec Digger Derrick ↗

    Related on MPF: Altec Industries in the Solutions Guide

  23. Dec. 7, 2018 Altec Aerial Device, Digger Derrick, Service Body Utility and aerial 2017–2018 Exterior lighting: brake lights 156 units 18V873000

    Defect

    Altec Industries, Inc is recalling certain 2017-2018 Digger Derrick, Aerial Devices, and Service Body vehicles, equipped with Whelen accessory brake lights. Depending on the specific wiring of the vehicle, these brake lights may illuminate when the brake pedal has not been pressed. As such these vehicles fail to comply to with the requirements of Federal Motor Vehicle Safety Standard FMVSS 108, "Lamps, Reflective Devices, and Associated Equipment."

    Consequence

    If the brake lights incorrectly illuminate, it can confuse other drivers, possibly increasing the risk of a crash.

    Remedy

    Altec will notify owners, and dealers will replace the brake lights, free of charge. The recall began February 7, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 708.

    Altec Industries Inc. · maker’s number CSN 708 · owners notified Feb. 7, 2019 · NHTSA page for the 2018 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  24. Nov. 28, 2018 Altec Aerial Device Utility and aerial 2017 Equipment 49 units 18V847000

    Defect

    Altec Industries, Inc. (Altec) is recalling certain 2017 Altec AT37, AT41 and AT48 aerial devices. Some of the fasteners that secure the pedestal to the chassis may be missing or may be loose which can cause a loss of stability or separation of the pedestal.

    Consequence

    A pedestal that is not secure can increase the risk of injury.

    Remedy

    Altec will notify owners and will repair the vehicles, free of charge. The recall began January 31, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 706.

    Altec Industries Inc. · maker’s number CSN 706 · owners notified Jan. 31, 2019 · NHTSA page for the 2017 Altec Aerial Device ↗

    Related on MPF: Altec Industries in the Solutions Guide

  25. Nov. 9, 2018 Terex Digger Derrick Utility and aerial 2017–2018 Structure 1,275 units 18V794000

    Defect

    Terex South Dakota, Inc. (Terex) is recalling certain 2017-2018 Terex Digger Derrick vehicles. The guide bar that attaches the pole guide arms to the pole guide tilt bracket may have insufficient welds, possibly resulting in the guide arm falling while in use.

    Consequence

    If the pole guide arm falls, it may strike any nearby personnel, increasing the risk of injury.

    Remedy

    Terex will notify owners, and dealers will replace the affected guide bars, free of charge. The recall is expected to begin December 14, 2018. Owners may contact Terex at 1-605-882-4000. Terex's recall number for this recall is SN669.

    Terex South Dakota, Inc. · maker’s number SN669 · owners notified Dec. 14, 2018 · NHTSA page for the 2018 Terex Digger Derrick ↗

Recall details are NHTSA’s and CPSC’s own text. Fleet classes are MPF’s grouping of NHTSA makes and models; police variants are often filed under the civilian model name, so also search the civilian model. Check every vehicle by VIN at nhtsa.gov/recalls.